The single drum vs double drum roller choice comes down to the material. A single drum roller vibrates hard and deep for soil, gravel and rock fill. A double drum roller, also called a tandem roller, uses a small, fast vibration and water spray for asphalt. LICH lists two machines that make the comparison unusually clean: the LCS214H and the LC214 both weigh 14 t and both have a 2,100 mm drum, so nearly every difference in this single drum vs double drum roller comparison comes from the layout.
Single drum vs double drum roller: the same 14 t, side by side
| LCS214H single drum | LC214 double drum | |
|---|---|---|
| Operating mass | 14,000 kg | 14,000 kg |
| Drum width | 2,100 mm | 2,100 mm |
| Static linear load | 326 N/cm | 333 N/cm |
| Amplitude (high / low) | 1.7 / 0.8 mm | 0.8 / 0.4 mm |
| Vibration frequency | 29 / 35 Hz | 40 / 46 Hz |
| Centrifugal force | 290 / 180 kN | 160 × 2 / 90 × 2 kN |
| Rear of the machine | Rubber tyres, 17.5-25 | Second vibrating steel drum |
| Water spray | Not part of the layout | 2 × 600 L |
| Rated power | 110 kW | 110 kW |
| Travel speed | 0–12 km/h | 0–12 km/h |
Figures from the LICH product catalogue, read on 6 November 2026.
What the numbers show
- Weight on the drum is nearly equal. 326 N/cm against 333 N/cm, a 2% difference. Static load does not separate these two machines.
- Amplitude is about twice as large on the single drum. 1.7 mm against 0.8 mm at high setting. A long stroke pushes energy deep into a thick layer of soil or stone.
- Frequency is higher on the double drum. Up to 46 Hz against 35 Hz. Small, quick strokes close up hot asphalt without crushing the stone in the mix.
- Force is split on the double drum. The single drum puts 290 kN through one drum. The double drum has 160 kN on each, 320 kN in total, and every pass of the machine compacts the strip twice.
- Water belongs to asphalt work. The LC214 carries two 600 L tanks to keep hot mix from sticking to the steel.
The amplitude and frequency guide goes further into why those settings suit each material.
Which roller for which job
Here is the single drum vs double drum roller decision by job:
| Job | Choose | Why |
|---|---|---|
| Soil, sand and gravel road base | Single drum | Large amplitude reaches a thick layer; tyres grip loose ground |
| Rock fill and dam foundations | Single drum | High force at low frequency; available up to 18 t |
| Asphalt base and wearing course | Double drum | Small amplitude, high frequency, water spray |
| Finish rolling with no tyre marks | Double drum | Steel at both ends leaves a smooth surface |
| Paths, trenches and patches | Small double drum | Models from 560 kg to 3.3 t fit tight spaces |
| Sealing an asphalt surface | Pneumatic tyre roller | Kneading action closes the surface; see the pneumatic tyre guide below |
See the pneumatic tyre roller guide for that third option and road roller types for all the layouts.
How the two ranges compare by size
We sorted the LICH catalogue of 12 single drum and 10 double drum models by weight. The two ranges overlap less than you might expect:
| Weight | Single drum models | Double drum models |
|---|---|---|
| Under 1 t | LC600 (330 kg, walk-behind) | LC600 (560 kg, walk-behind), LC700Z (800 kg) |
| 1–3.3 t | None listed | LC800, LC900, LC1000, LC1100, LC1200, LC203 |
| 8 t | LCS208H | LC208 |
| 10–12 t | LC210B, LCD210H, LC212B, LCS212H, LCD212H | None listed |
| 14 t | LCS214H, LCD214H | LC214 |
| 16–18 t | LC216B, LCD216H, LCS718H | None listed |
So small jobs lead you to a double drum, and heavy earthworks to a single drum. Among larger machines, the real choice of layout comes at 8 t and 14 t, where both exist. The road roller weight chart gives every figure.
Three questions that settle single drum vs double drum roller
- What are you compacting? Soil or stone points to a single drum; asphalt to a double drum.
- How thick is the layer? Thick lifts need amplitude and force; thin lifts need frequency.
- How will the site run? On a road project with both earthworks and paving, plan one of each. A 12 ton road roller is a common choice for the base, with a double drum for the asphalt.
Questions about single drum vs double drum rollers
Is a tandem roller the same as a double drum roller?
Yes. Both names describe a roller with a steel drum at the front and rear. See the tandem range.
Can a single drum roller compact asphalt?
It is built for soil and stone. Its large amplitude and rear tyres suit that work, and the asphalt roller guide explains what paving calls for.
Which one is better on soft ground?
A single drum, because the rear tyres drive on loose or uneven ground, where steel drums can slip.
Which has more compaction force?
At 14 t, the single drum has more force on one drum (290 kN against 160 kN), and the double drum has more in total (320 kN against 290 kN).
Tell us what you are compacting, the layer thickness and the site. We will settle single drum vs double drum roller for your job, recommend a model from the LICH range and send a written quotation with the configuration and shipping method.
Related reading: compare every layout in the vibratory rollers range.
Related reading: what is a road roller covers the parts and the three ways a roller compacts, and the mini road roller guide lists nine models from 330 kg to 3.3 t.